Comments on: Control ESP32/ESP8266 GPIOs from Anywhere (Firebase Web App)

By: Sara Santos

Sara Santos — Sat, 18 Jan 2025 11:09:10 +0000

Hi.
Open the JAvascript console and see if you get any errors.
Also, hard refresh your web browser.
Regards,
Sara

By: vijay sinh

vijay sinh — Sat, 18 Jan 2025 10:37:59 +0000

In reply to Sara Santos. hi get everything fine also get web app successfully but there no any login form it just showing only title of web app and header

By: Arturo

Arturo — Fri, 08 Nov 2024 20:11:13 +0000

In reply to Sara Santos.

I get the following errors and have the same issue:

index.js:24 Uncaught SyntaxError: Identifier ‘dbPathOutput3’ has already been declared
auth.js:10 user logged out
subscribe.ts:239 ReferenceError: setupUI is not defined
at Object.next (auth.js:11:13)
at subscribe.ts:104:16
at subscribe.ts:233:11

By: Anbjørn Myren

Anbjørn Myren — Sun, 25 Aug 2024 21:38:16 +0000

In reply to Henry Leonardo Campos García.

Hi.
Its been a while since I set it all up so I dont remember every step in the process.
My setup is now with one NodeMCU receiver unit which have a 8 channel solidstate relay card connected so I can control 8 outputs.

I have 8 Wemos D1 Mini v3.0.0 with temp/humidity/pressure sensor that sends their values every 10 minute to the NodeMCU receiver. The NodeMCU compares the temperature value to check if it is higher or lower than the setpoint for the actual channel and sets the corresponding output on or off.

The NodeMCU also sends the values to the Firebase database, and also reads the setpoint values from the database. From the web-app webpage I can monitor all these 8 sensors and also change the setpoint values.
The NodeMCU also acts as a webserver, html code is nearly similar to the web-app, but it also have a timestamp so I can see when the values was last updated.

I did choose the Wemos boards for the sender units because their low standby power consumption, only about 8 microamp in deep standby. I set them to wake every 600 sec, transmit their value and return to deep sleep again. This way I can use 18650 3.7v batteries to power them and they lasts for months before recharge is needed.

By: Paulus Andi Nalwan

Paulus Andi Nalwan — Sat, 24 Aug 2024 03:42:56 +0000

Hi, I have reach step 18 but found error loading firebase SDK please check console. Could you let me know the solution?

By: Henry Leonardo Campos García

Henry Leonardo Campos García — Wed, 03 Jul 2024 20:11:34 +0000

In reply to Anbjørn Myren. Hello Myren, how did you solve it? Everytime i tried to set the new value the setup() function executes again, so I don't know what to do

By: Juan criado

Juan criado — Wed, 31 Jan 2024 17:00:17 +0000

Hello, I have completed the tutorial and it works well for me.
I have been testing if it was possible that by pressing a single button, it activates a relay, leaves it activated for a second, and then deactivates it again.
My intention is to use it to open a garage door, but I can’t, and I was wondering if you could help me. So far the only thing I have achieved is that when I press it, the relay is activated, and in a very few milliseconds it turns off, but I needed the relay to be activated for longer.
I attached the button code:
btn6On.onclick = () =>{
dbRefOutput5.set(1);
setTimeout(() => {
console.log(“1 second please”)
}, 1000);
dbRefOutput5.set(0);
}

PD: With this code the relay is activated, but it turns off immediately, and the 1 second delay does not do it for me, I hope you can help me, I have already looked elsewhere and I cannot find the solution.
I would greatly appreciate your help. Good morning.

By: Raajshekhar Rajan

Raajshekhar Rajan — Wed, 21 Jun 2023 08:50:32 +0000

hi sara, your projects are of gr8 help, I made it on 1st go. But I have a question, like I want to create 2 different users with different board and no one can control or see each other. Is there a way?

By: JJ

JJ — Thu, 23 Mar 2023 05:26:25 +0000

after I install all the Visual Studio Code,Node.JS LTS version,Install Node.js Extension Pack (VS Code),Install Firebase Tools and run the ‘Initializing Web App Firebase Project’, I got the msg ‘Firebase initialization complete!’ and ‘Deploy complete!’. But I cannot find the 404.html or the index.html and all the other stuffs from the left side bar of the VS studio, help plz, thank you

By: Sara Santos

Sara Santos — Sun, 19 Mar 2023 12:31:12 +0000

In reply to BAASKAR.

Hi.
What happens exactly?
Can you provide more details?
Regards,
Sara